Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
What are your opinions concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately challenging task. If the old bathtub is conveniently available, the task can relocate quickly; if you have to open up a wall surface to get rid of the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices as well as material checklist ought to comprise the following:
Getting ready for the Setup
Firstly, the supporting structure provided with the bathroom must be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water system. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit all-time low of the furthest versatile tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill the bath tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub must wait up until the tub has been made use of at the very least when as this will certainly settle it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The former kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to fracture a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing spaces approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm very eager about Tools You Need to Install a New Bathtub and I'm hoping you liked the new entry. Sharing is nice. You just don't know, you might be helping someone out. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Call Us Today
Report this page